Plume ville V1.5 RDA clone sold out

Features:
Stainless steel body
22mm diameter
Dual, single or quad coil compatible
Phillips screws
Deep juice well
Milled negative posts, no turning, EVER!
Adjustable single or dual air-flow
Unique airflow brings air from 3 places - slots in front of coils, holes through negative posts & holes in top cap for vacuum effect!
Engraved logo
Delrin insulator
Gold plated base and negative posts, along with 510 contact
Stainless steel positive block

Includes:
Plume Veil RDA clone
Extra O-Rings
Extra Screws
Tool

Price SS 600THB. (V1.5)
Ems Shpping in Thailand 50THB.

 

Re: Plume ville RDA clone

My cap can be tight and hard to lift off too sometimes but not always and not sure why exactly. What I found helps is rocking/tilting the top cap side to side a bit as I pull up....works well.

Agreed, can be easy to overfill so need to work out number of drips and kind of keep that in mind...I am doing about 10 to 12 drips before the point where I think I may soon get a dry hit. Haven't had a leak since. I need to try and see if she can take a little more.

 

Re: Plume ville RDA clone

After 3 Coils i found a good one .. but it really sucks to take of the Top Cap .. already my fingers hurt just from that ..it's to tight and probably the only difference to the Original !

 

Re: Plume ville RDA clone

Hi Sammy - Have you tried rocking it back and forth and pulling.....when I do this now it comes off pretty easily and consistently. If I dont do it this way it can be hard to take off

 

Re: Plume ville RDA clone

tired .. 2 of my fingers still red.. i really like to Vape him but i hate to use it already cuz of that tight Cap !!! It's no fun anymore if i start think about to open that sucker ..

 

Re: Plume ville RDA clone

Sorry to hear that Maybe it'll loosen up some later. Another option I had used was just not to push the cap down 100% and leave a small gap...didn't seem to affect the airflow any when I tried that. Hope you can get something worked out!

 

I am thinking of getting one in the future. And yes bought one for my brother and it was really not easy to get off.


But I really love the airflow. For the taste and vape still need to try

 

Re: Plume ville RDA clone

If you haven't already, try lubing your o-rings with a bit of juice. Generally will help.

Mine is the same BTW and the top of the cap is nearly impossible to get off.

 

Re: Plume ville RDA clone

I vasalined the inner top and o ring and it is fine. Mega vape. Brilliant airflow and looks the business.

 

Re: Plume ville RDA clone

i need a drip tip like that ..from where u get it ??

 

Re: Plume ville RDA clone

Once the RDA is in use the parts can easily be separated as they are full of juice. What build are you guys using?
BTW is there a special way to wick this RDA so the juice is not ruining out from the air holes on the negative post at the bottom?

 

Re: Plume ville RDA clone

Got them from Big Mflux Derlin Drip tips

 

Re: Plume ville RDA clone

As far s build I am only using it on my 30W devices atm, but plan to try a sub ohm build on a mech soon.

Leaking from the Neg post airholes isn't a problem unless you over drip significantly or tilt it so a neg post is down while not drawing. Other than that no problems.

- - - Updated - - -

I should clarify that I was using 50/50 juice and was adjusting the atty at teh time of the leak so there was time for the juice to pool around the neg post

- - - Updated - - -

Finally….I just put a nice 25g dual parallel at 0.16 in to one of my Plume Veils. As you would expect good vapor and flavour. BUT for a build that is normally a touch too warm for me it was surprisingly relatively cool. Normally I would do this as a standard dual 24g or 22g and this is only marginally hotter than that kind of build. My ADV build is around the 0.2-0.3 ohm dual coil.